Rubber Supports for ROMEICO Automotive Lifts

ROMEICO is known to many workshops primarily as an older established brand in the field of automotive lifts and workshop equipment. ROMEICO lifts are still frequently found on the used equipment market today. For spare parts, older two-post lifts such as H225, H230, Atlantic and Nordmeer are particularly relevant.

For ROMEICO automotive lifts, we offer suitable rubber pads, rubber supports, rubber lift supports, lifting pads, support plates and replacement rubber pads for various models. Especially with older lifts, accurate identification is important because support plates, old rubber components, year of manufacture and possible modifications may differ.

At Böck®, you will find robust premium rubber pads for ROMEICO automotive lifts that can replace worn or damaged rubber supports. Many common versions are available at short notice, helping older lifts remain reliable in everyday workshop use. The model list provides an initial guide. However, reliable product selection should always be based on the dimensions, the existing metal support plate and the technical drawing on the respective product page.

Compatible Models

For these ROMEICO models, we offer suitable rubber pads, rubber supports and relevant replacement parts. The model names provide guidance when searching for the correct replacement rubber pad, rubber support or suitable support plate.

Important Older ROMEICO Two-Post Lifts

• H225
• H230
• H224/FOG 449
• Atlantic
• Atlantic 2.0
• Nordmeer

Spare Part Assignments from Dealer and Spare Part Sources

• H225
• H226
• H227
• H230
• H231
• H232
• FOG 444

ROMEICO / Beissbarth Spare Part and Model Designations

• R224
• R225
• R230
• R231
• R235
• R236
• R237

Additional ROMEICO Model Designations from PDF, Search and Market Sources

• SA 235 S
• SA 250 S
• SA 455 M
• SA 135 DZ X
• FC 235 M
• FC 135 DZ H
• AT 235 FC
• AT 250 FC
• AT 440
• AT 440 AV

Relevant Dimensions for ROMEICO Rubber Supports

• Ø160 x 25 mm
• 150 x 80 x 28 mm

How to Choose the Correct Rubber Pad for ROMEICO

With ROMEICO, accurate identification is particularly important because many automotive lifts have already been in use for several decades. A rubber support for an H225 does not automatically fit an H230, Atlantic, Nordmeer or H224/FOG 449. Even if spare part suppliers list certain models together, you should always check which metal support plate is actually installed on the lift.

An operating manual for the H225 and H230 is available under the name “Romeico-Lift”. It lists the H225 with a lifting capacity of 2,500 kg and the H230 with 3,000 kg. These models are particularly important for spare part searches because customers often search directly for terms such as ROMEICO H225 rubber pad, ROMEICO H230 rubber support or ROMEICO replacement rubber pad.

Spare part sources list a round slip-on rubber pad measuring Ø160 x 25 mm for ROMEICO H225, H226, H227, H230, H231, H232, Atlantic, Nordmeer and FOG 444. For Atlantic and Nordmeer, a rectangular rubber support measuring 150 x 80 x 28 mm is also relevant. These dimensions are very useful for identification, but they do not provide a general compatibility guarantee. The existing component on your own automotive lift should always be used as the reference.

As differences may occur depending on the year of manufacture, version or installed support plate, you should always measure the existing support plate yourself before ordering. Compare the dimensions with the technical drawings and measurements on the respective product page. This helps prevent incorrect orders and makes it much easier to identify the correct rubber support for your ROMEICO automotive lift.

Understanding ROMEICO, Beissbarth, Rohé and FOG

Various connections to other brands appear in older ROMEICO documentation and spare part sources. One of the better documented connections is with Beissbarth/Rohé for certain older models. An operating manual explicitly refers to “Romeico-Lift”, the H225/H230 models and Beissbarth Rohé automotive workshop equipment in the document and company context.

Names such as Beissbarth-Romeico, H224/FOG 449 or FOG 444 may also appear when searching for spare parts and rubber supports. These references can be useful, but they do not replace a technical compatibility check. Rubber pads and support plates should not be ordered solely on the basis of a similar model designation, but should always be checked according to dimensions, support shape and the existing part.

It is also important to distinguish between older ROMEICO lifts still in operation and potentially newer ROMEICO web or PDF model designations. Models such as SA 235 S, SA 250 S, SA 455 M, SA 135 DZ X, FC 235 M, FC 135 DZ H, AT 235 FC, AT 250 FC, AT 440 and AT 440 AV should not automatically be treated as equivalent to historical ROMEICO automotive lifts from the 1970s to the 1990s.

ROMEICO Rubber Supports for Atlantic, Nordmeer, H225 and H230

Especially on older ROMEICO two-post lifts, rubber pads and rubber supports are typical wear parts. Daily use, vehicle weight, oil, dirt and ageing can cause the rubber components to become hard, cracked or damaged. Replacing them in good time helps protect the vehicle’s lifting points and ensures a clean, reliable contact surface on the support plate.

Round ROMEICO rubber pads for H225, H226, H227, H230, H231 and H232 are frequently requested. Atlantic and Nordmeer are also very relevant in the spare parts market. For Atlantic and Nordmeer, a rectangular rubber support may additionally be required. Before ordering, you should therefore always check whether you need a round slip-on rubber pad or a rectangular rubber support.

On used ROMEICO automotive lifts, support plates, lifting arms or lifting supports may have been replaced over the years. Some lifts have been repaired, modified or kept in operation using components from other manufacturers. For this reason, comparing the existing rubber pad and metal support plate is particularly important.

Not Sure? We Can Check Your Details

You are also welcome to contact us by email. For reliable identification, we require photos of the automotive lift’s nameplate, a top-view photo of the existing rubber pad and the dimensions of the support plate.

The diameter and height are particularly important. If the rubber pad has more than one hole, we also require the centre-to-centre hole spacing. For rectangular rubber supports, please also provide the length, width and height. For older ROMEICO support plates, the plate shape, metal edge, slip-on dimensions, hole and fastening system are also important.

Photos of the lifting arm, metal support plate and old rubber component from the top, bottom and side are also helpful, along with details of the model number, serial number, lifting capacity and condition of the old rubber support. We compare your information with the available Böck® rubber pads and rubber supports. Not sure which product you need? Send us your photos and measurements.

Böck® Quality for Older ROMEICO Automotive Lifts

Rubber pads, replacement rubber pads and rubber supports are small components, but they perform an important function in everyday workshop use. They protect the vehicle’s lifting points, improve the contact surface and replace worn or damaged supports on the automotive lift.

At Böck®, we focus on durable materials, precise workmanship and high load capacity for everyday professional use. Especially on older ROMEICO automotive lifts, replacing worn rubber supports is worthwhile because the lift itself is often still mechanically sound while the old rubber components have significantly aged.

Many common premium rubber pads for ROMEICO, Atlantic, Nordmeer, H225 and H230 are available at short notice. To ensure you order the correct product, we always recommend comparing the existing component with the dimensions provided on the product page. If the model number, support shape and dimensions match, the correct rubber support for ROMEICO can be identified much more reliably.

FAQ

• 1. Which rubber pad fits my ROMEICO H225 or H230?
  Spare part sources list round slip-on rubber pads measuring Ø160 x 25 mm for the H225 and H230. However, you should always check the existing metal support plate, old rubber component and nameplate. With older lifts, the year of manufacture, modifications or replaced support plates may lead to differences.
• 2. Do Atlantic and Nordmeer use the same rubber supports?
  Not automatically. Atlantic and Nordmeer are often listed together in spare part sources, including round rubber pads measuring Ø160 x 25 mm and rectangular rubber supports measuring 150 x 80 x 28 mm. The decisive factor is which lifting support is actually installed on your automotive lift.
• 3. Why order Böck® rubber pads for older ROMEICO automotive lifts?
  Böck® rubber pads are robust, durable and designed for regular professional workshop use. Many common versions for older ROMEICO automotive lifts are available at short notice. This allows worn rubber supports to be replaced correctly so that existing lifts can continue to be used.